High pressure X-ray diffraction study of CdAl2Se4 and Raman study of AAl2Se4 (A=Hg, Zn) and CdAl2X4 (X=Se, S)

We report the results of an X-ray diffraction study of CdAl₂Se₄ and of Raman studies of HgAl₂Se₄ and ZnAl₂Se₄ at room temperature, and of CdAl₂S₄ and CdAl₂Se₄ at 80 K at high pressure. The ambient pressure phase of CdAl₂Se₄ is stable up to a pressure of 9.1 GPa above which a phase transition to a disordered rock salt phase is observed. A fit of the volume pressure data to a Birch-Murnaghan type equation of state yields a bulk modulus of 52.1 GPa. The relative volume change at the phase transition at ∼9 GPa is about 10%. The analysis of the Raman data of HgAl₂Se₄ and ZnAl₂Se₄ reveals a general trend observed for different defect chalcopyrite materials. The line widths of the Raman peaks change at intermediate pressures between 4 and 6 GPa as an indication of the pressure induced two stage order-disorder transition observed in these materials. In addition, we include results of a low temperature Raman study of CdAl₂S₄ and CdAl₂Se₄, which shows a very weak temperature dependence of the Raman-active phonon modes.     

测定麦芽糖转糖苷反应体系组成的高效液相色谱法

建立了分析低聚异麦芽糖组成的高效液相色谱法，采用Spherisorb-NH2色谱柱，示差折光检测器，乙腈－水（体积比70：30）为流动相，外标法定量测定；结果显示各糖质量浓度在0．1－10g/L范围内与峰面积呈良好线性关系，相关系数为0．999 0－0．999 7；应用法跟踪了pH5．0的柠檬酸－柠檬酸钠缓冲溶液中以α－葡萄糖转苷酶为催化剂在58℃温度下的麦芽糖转糖苷反应，分析了反应体系组成随时间的变化，得到了上述反应条件下麦芽糖最大限度地转化为低聚异麦芽糖的最佳反应时间为24h；该法快捷、简单、准确，可用于低聚异麦芽糖生产的质量控制。     

BEPCⅡ大功率波导真空阀门的研制

 大功率波导真空阀门是BEPCⅡ直线加速器微波系统的重点改进项目，作为微波大功率传输和真空密封双重功能的超高真空微波器件，机械结构比较复杂，制造工艺难度大。经过各方努力，已经研究完成16台大功率波导真空阀门，并在2004年全部安装在加速器上使用。目前进入到波导真空阀门的脉冲功率为30~50 MW，高功率运行工作状态良好。对阀门从设计原理、机械结构、微波测试及高功率运行等方面作了较详细的阐述。     

用能量法求多自由度振动系统的角频率

利用简谐振动能量方程，通过分析振幅矢量的关系，用能量法求多自由度振动系统的角频率或简正振动频率。     

Modification of the surface state of rough substrates by two different varnishes and influence on the reflected light

Modification of the visual appearance when a rough surface is covered by a varnish is mostly attributed to the levelling of the substrate surface, which depends on the molecular weight of the varnish. The topography of varnished surfaces, however, has never been measured directly. Surfaces of varnishes applied over glass substrates of varying roughness were studied, therefore, using mechanical profilometry. Two different varnishes made with a low and a high molecular weight resin were studied. Both varnishes lower the r.m.s. roughness of the substrates and filter the high spatial frequencies. These results are amplified for the varnish containing the low molecular weight resin. The light reflected by the varnished samples is modelled from these topographical data. Its angular distribution, calculated from the probability density of slopes is presented, taking into account separately the air/varnish and the varnish/substrate interfaces. These analyses are presented in a back-scattering configuration. They show that varnishing significantly reduces the angular width of the reflected light and that this effect is magnified for the low molecular weight resin. Modelling furthermore shows that the influence of the roughness of the varnish/substrate interface is negligible in the total reflected light.     

High-throughput screening of fuel cell electrocatalysts

The drawbacks of our earlier report of preparing fuel cell catalyst arrays by borohydride reduction of inkjet prepared arrays of metal salts are discussed along with the need for inclusion of state-of-the-art metrics in all array screening. An alternative method for screening of hydrogen/air cathode catalysts, direct methanol fuel cell (DMFC) anode catalysts, and catalyst loading studies is provided. State-of-the-art Johnson Matthey catalysts were used in control experiments to demonstrate the utility of the array fuel cell for high throughput screening of fuel cell catalysts in the 3-4 mg/cm² range. This report lays out hard learned rules for high throughput screening and demonstrates that the array fuel cell can be used for very precise screening of libraries of membrane electrode assembly (MEA) components without the pitfalls discussed in the introduction.     

All-optical frequency multiplication/recovery based on a semiconductor optical amplifier ring cavity

A novel scheme for all-optical frequency multiplication/recovery based on a semiconductor optical amplifier ring cavity is proposed and investigated numerically. The results show, for a 2.5 GHz driving pulse train, it can be generated 5-25 GHz repetition rate pulse trains with low clock amplitude jitter, polarization independence and high peak power. Furthermore, the extraction of the clock signal from a pseudorandom bit sequence signal can be realized based on the proposed scheme.     

Comparison of growth stress measurements with modelling in thin iron oxide films

High temperature oxidation of metals leads to residual stresses both in the metal and in the growing oxide. In this work, the evolution of this residual stresses is theoretically predicted in the growing oxide layers. The origin of these stresses is based on a microstructural model. Using experimental results providing from the oxidation kinetics, and an analysis proposed to describe the growth strain occurring in the thin layers, a set of equations is established allowing determining the stresses evolution with oxidation time. Then, the model is compared with experimental results obtained on both α-Fe and phosphated α-Fe, oxidised at different temperatures. Numerical data are extracted from experiments either with an asymptotic formulation or with an inverse method. These two methods give good agreement with experiments and allow extracting the model parameters.     

一种高信噪比的双光束激光光声光谱仪原理及应用

作为一种新兴的检测手段 ,激光光声光谱技术与其他检测技术相比具有很多优点。本文设计的光声光谱仪用激光做光源 ,有两个光声池 ,分别用来放置参考样品和待测样品 ,输出结果为二者光声信号的比值。利用这一比值 ,可以由参考样品的性能参数方便地求出待测样品的相关性能参数。该光声光谱仪有效地减小了本底吸收噪声的影响 ,提高了信噪比 ,扩大了固体光声理论的应用范围。本文还阐述了该光声光谱仪在定性定量分析中的一些应用     

New FIR laser lines and frequency measurements for optically pumped CD3OH

Twenty new cw FIR laser lines in CD₃OH, optically pumped by a CO₂ laser, are reported. The frequencies of 39 of the stronger laser lines were measured relative to stabilized CO₂ lasers with a fractional uncertainty, as determined by the reproducibility of the FIR frequency itself, of 2 parts in 10⁷.Contribution of the U.S. Government, not subject to copyright.